Guy Grip Quality Inspection Checklist

Inspection on this product is not about checking everything — it is about checking the handful of characteristics where a defect would survive installation, be invisible at the time, and fail later. Those characteristics are known, and they can be written into an inspection plan in an afternoon.

This is that plan for guy grips.

Start from the failure modes, not from the drawing

The three defects that actually cost money on this product:

• 1. Grip slipping on the strand. helix pitch formed for a nominal strand diameter that does not match the actual strand — always confirm the strand construction, not just the diameter
• 2. Wire ends damaging the operator or the strand. ends cut and left sharp instead of deburred and colour coded

Every inspection point below exists to catch one of those, or to catch the material and dimensional drift that produces them.

What a guy grip must be checked against

galvanised steel wire or stainless steel wire, preformed helix is the specified material; the accepted grades are galvanised steel strand; AISI 304 stainless; AISI 316 for coastal and chemical sites. The governing standard is ASTM A475, IEC 61395, and the dimensions covered are strand diameter 6–20 mm, leg lengths 300–1200 mm, helix pitch matched to strand construction.

Write those four facts at the top of the inspection plan. An inspector with no specification will measure what is easy to measure and pass the batch.

Incoming material check

1. Grade evidence: a mill certificate or a supplier declaration of grade is the minimum; on stainless, an XRF check on a sample settles it in minutes.
2. Material condition: straightness, surface defects, inclusions, delimitation or porosity visible before forming.
3. Pre-coating preparation: degreasing and pickling evidence where the finish depends on it — a coating over a contaminated surface fails as a whole.

Dimensional inspection

Against strand diameter 6–20 mm, leg lengths 300–1200 mm, helix pitch matched to strand construction:

1. Measure the functional dimensions, not just overall size — the dimensions that make the part fit are the ones a supplier is most tempted to run loose.
2. Check the dimensions that govern assembly: hole patterns, thread forms, radii and interface faces.
3. On a sample of 5–10 pieces, measure with the same instrument the specification nominates. Two methods give two answers.

Finish and coating

hot-dip galvanised strand or bright stainless, ends deburred and colour coded by size

1. Measure coating thickness or coating mass on a sample per batch, at three points including a cut edge.
2. Look specifically at cut ends, drilled holes and bend radii — coatings fail there first.
3. Check for coating damage from handling and packing, which is a supplier process problem, not a product problem.

Mechanical and electrical tests

Your specification should name these; the inspection should confirm they were run and the records kept:

• hold test at rated tension — confirm the certificate, the sample size and the date.
• helix pitch measurement — confirm the certificate, the sample size and the date.
• salt spray 480 h — confirm the certificate, the sample size and the date.
• visual check for wire damage — confirm the certificate, the sample size and the date.

Per ASTM and ISO sampling practice, an inspector normally works to an AQL of 1.0 for major defects and 2.5 for minor ones unless your order says otherwise. Agree the definition of “major” in advance — on this product, anything affecting load path or coating integrity is major.

Pre-shipment inspection checklist

1. Quantity and part numbers against the packing list.
2. Dimensional sample per the plan above.
3. Coating or finish measurements recorded with photographs.
4. Functional test on an assembled sample where the product is supplied as a set.
5. Marking and labelling correct on the product, the bag and the carton.
6. Packing verified: 25 pcs per bundle, size labelled.
7. Test records and certificates present and matching this batch.
8. Container loading supervised, with seals recorded.

If a batch fails

Do not start with a price discussion. Start with three questions: how many pieces are affected, what is the containment, and what is the root cause. A supplier who can answer all three is a supplier you can keep. On this product the usual resolutions are a 100 % sort, a rework of the coating or finish, or a re-run — and the cost of the sort should be settled before the goods move, not after.

Related: the guy grip specification guide is where the tolerances this inspection measures should be defined in the first place, and the supplier selection guide covers what to ask before you get to this stage.