Cable Attachment: Complete Buyer's Guide

Cleats, clamps, brackets and stainless ties — small parts, but the ones that decide whether a cable run survives fault current and wind.

This hub collects the 4 product families in this category and the buying guides behind each one — specifications, price drivers, quality inspection and supplier selection — so a buyer can move from category level down to a specific part without leaving the English section.

Product families in this category

• Cable Cleat — cable cleat, cable clamp cleat, short circuit rated cleat. Tray and ladder cable fixing.
• Cable Clamp — cable fixing clamp, cable saddle clamp, conduit clamp. Fixing cable to walls and struts.
• Cable Bracket — cable support bracket, hook bracket, pole bracket. Supporting aerial cable on poles.
• Stainless Steel Cable Tie — SS cable tie, metal zip tie, ball-lock tie. Outdoor cable fixing where nylon fails.

What decides quality across this whole category

Three things repeat across every product here, and they are worth stating once at category level:

1. Grade discipline. Whether it is aluminium alloy or polymer body with an elastomer insert or a polymer, the grade is what separates a fifteen-year part from a three-year part, and it is invisible in the finished product.
2. Coating and surface preparation. Nearly every field failure in this category starts at a cut edge, a bend or a crimp where the surface protection was broken or never properly applied.
3. Test evidence per batch. A type test qualifies a design; only routine test records tell you what you actually received.

Sourcing context in Hebei

• Cable Cleat — cast and moulded in Botou and Nanpi, with the elastomer inserts from Hebei’s rubber processors and aluminium bodies from the regional casting trade.
• Cable Clamp — pressed and galvanised at volume in Nanpi and Yongnian, where the presswork and coating lines are set up for exactly this class of part.
• Cable Bracket — stamped, formed and galvanised in Nanpi and Botou, with hole patterns adapted from standard aerial hardware.

How to work through this category

Start with the sourcing guide for the specific part you need, because it forces the specification decisions in the right order: dimension, grade, standard, finish, test, packing. Then use the price guide to interpret the quotations you receive, and the quality checklist to write the inspection plan before the goods are made rather than after.

Cable Cleat

Aluminium alloy or polymer body with an elastomer insert. Common grades: LM6 aluminium, glass-filled nylon body, silicone insert for high temperature, EPDM insert as standard. Typical specification range: cable diameter 10–120 mm, single or trefoil arrangement, short-circuit rating 40–150 kA peak. Governing standards: IEC 61914, EN 50368. Typical minimum order 300 sets, lead time 25–40 days.

Cable Clamp

Galvanised steel or stainless steel, usually with a rubber or PVC liner. Common grades: Q235 hot-dip galvanised, AISI 304 stainless, nylon liner, EPDM liner. Typical specification range: cable diameter 6–80 mm, single and two-bolt patterns, wall or strut mounted. Governing standards: ISO 1461, ASTM A153. Typical minimum order 2,000 pcs, lead time 18–28 days.

Cable Bracket

Galvanised steel or stainless steel. Common grades: Q235 hot-dip galvanised, AISI 304 stainless, AISI 316 for coastal. Typical specification range: arm length 150–600 mm, load capacity 0.5–5 kN, pole mounting or wall fixing. Governing standards: ISO 1461, ASTM A153. Typical minimum order 500 pcs, lead time 20–30 days.

Stainless Steel Cable Tie

Stainless steel strip with a ball-lock or ladder-lock head. Common grades: AISI 304, AISI 316, AISI 201 for indoor use, PVC or epoxy coated variants. Typical specification range: length 100–1500 mm, width 4.6–12 mm, tensile 0.5–4.5 kN, ball-lock or ladder-lock. Governing standards: ASTM A666, IEC 61914. Typical minimum order 5,000 pcs, lead time 15–25 days.